The Viper represents Fuchs Audio Technology’s continued evolution into amplifiers for the metal genre. Combining two great preamp designs with an all–tube hard-wire relay bypassed effects loop, and an exceptionally strong power amp, has produced a sonic force to be taken very seriously ! The Viper is a dual channel platform which features two distinctly different preamp voices for maximum tonal range.

The Viper Features

Channel one is a classic style mid driven American-voiced bluesy overdrive. While it has plenty of gain on tap, it also features a smooth warm and round overdrive tone. It can be run clean by lowering the input gain and raising the output master. High, Mid and Low controls offer a wide tonal range.

Channel two features a mid scooped traditional high gain metal voicing. An aggressive edge on the high end, an extended chunk on the low end, with amp gain to shred, hammer and scream, to your hearts delight. Both channels are pedal friendly and feature dedicated tubes for each channel (no shared tubes) to permit selecting tubes to enhance each channels tonal signature.

Low noise is assured through careful internal grounding, DC preamp tube filaments, as well as shielded audio cables and selected tubes throughout. The all-tube effects loop can be bypassed when not in use, and engaged via the rear panel loop switch. It also features high and low gain modes, for pedal or rack style effects use. The power amp features a high energy power supply with high speed switching diodes, a precision wound choke, and a large power supply reserve for tight controlled response up to full power. Like all Fuchs amps, it’s built on an aircraft grade aluminum T-6 aluminum chassis with fan cooling and stainless steel hardware throughout. A custom would output transformer has 4,8 and 16 ohm outputs, and is highly overrated and custom wound for Fuchs. The power stage features presence and thrust controls. Presence adjusts the high end response from smooth to edgy, while Thrust adjusts the level and tightness of the low end to get maximum bass from any speaker cabinet.

Units are CE and RoHs certified, available is 120 or 240 volt power configurations.

Front Panel Features:

Channel One: input gain output master, high mid low controls. Input jack
Channel Two features: input gain output master, high, mid, low controls.
Power amp features: presence and Thrust controls for high and low tailoring of power amp.

Rear Panel Features:

IEC International standard power connector for detachable power cord.
Fuse holder. AC Power, Standby, Ground polarity, 4, 8 16 ohm outputs, FX loop, FX Loop bypass switch, send output jack, return level trim switch,

Footswitch Jack:

Standard ¼” mono plug for channel switching

Features:

¾” solid wood cabinet with durable tolex covering.

Anodized aluminum chassis with long-lasting silk screened labeling on rear panel. Front panel is available in black. Crème or black knobs are available. Heavy duty Cliff brand jacks. Solid metal shaft Alpha potentiometers. Ultra-long-life LED pilot lamp and heavy duty AC power, standby, and ground switches. Power stage features control, and separate bias controls for each pair of power tubes.

By popular request, using EL-34 tubes for a great sparkle and grind, the Viper-50 is now available! The same great tone and feature set as the Viper, but in a lower power configuration.

Channel one is a classic style mid driven American-voiced bluesy overdrive. While it has plenty of gain on tap, it also features a smooth warm and round overdrive tone. It can be run clean by lowering the input gain and raising the output master. High, Mid and Low controls offer a wide tonal range.

Channel two features a mid scooped traditional high gain metal voicing. An aggressive edge on the high end, an extended chunk on the low end, with amp gain to shred, hammer and scream, to your hearts delight. Both channels are pedal friendly and feature dedicated tubes for each channel (no shared tubes) to permit selecting tubes to enhance each channels tonal signature.

Low noise is assured through careful internal grounding, DC preamp tube filaments, as well as shielded audio cables and selected tubes throughout. The all-tube effects loop can be bypassed when not in use, and engaged via the rear panel loop switch. It also features high and low gain modes, for pedal or rack style effects use. The power amp features a high energy power supply with high speed switching diodes, a precision wound choke, and a large power supply reserve for tight controlled response up to full power. Like all Fuchs amps, it’s built on an aircraft grade aluminum T-6 aluminum chassis with fan cooling and stainless steel hardware throughout. A custom would output transformer has 4,8 and 16 ohm outputs, and is highly overrated and custom wound for Fuchs. The power stage features presence and thrust controls. Presence adjusts the high end response from smooth to edgy, while Thrust adjusts the level and tightness of the low end to get maximum bass from any speaker cabinet.

Units are CE and RoHs certified, available is 120 or 240 volt power configurations.

Front Panel Features:

Channel One: input gain output master, high mid low controls. Input jack
Channel Two features: input gain output master, high, mid, low controls.
Power amp features: presence and Thrust controls for high and low tailoring of power amp.

Rear Panel Features:

IEC International standard power connector for detachable power cord.
Fuse holder. AC Power, Standby, Ground polarity, 4, 8 16 ohm outputs, FX loop, FX Loop bypass switch, send output jack, return level trim switch,

Footswitch Jack:

Standard ¼” mono plug for channel switching

Features:

¾” solid wood cabinet with durable tolex covering.

Anodized aluminum chassis with long-lasting silk screened labeling on rear panel. Front panel is available in black. Crème or black knobs are available. Heavy duty Cliff brand jacks. Solid metal shaft Alpha potentiometers. Ultra-long-life LED pilot lamp and heavy duty AC power, standby, and ground switches. Power stage features control, and separate bias controls for each pair of power tubes.

By popular request, using EL-34 tubes for a great sparkle and grind, the Viper-50 is now available! The same great tone and feature set as the Viper, but in a lower power configuration.

The Viper Specifications

VIPER-50

Weight (Head): 40 Lbs.
Tube compliment: 6 X 12AX7 preamp tubes,
2 X EL-34/6CA7 power tubes
50 W RMS into 4, 8, or 16 ohms.
Input Impedance -1 Meg.

FX Loop:
Output impedance 1-K. Signal; level up to 3 volts p/p
Return impedance 100-K sensitivity from 250 mv to 3 volts p/p

VIPER-100

Weight (Head): 50 Lbs.
Tube compliment: 6 X 12AX7 preamp tubes,
4 X 6550
100 W RMS into into 4, 8, or 16 ohms.
Input Impedance -1 Meg.
FX Loop:
Output impedance 1-K. Signal; level up to 3 volts p/p
Return impedance 100-K sensitivity from 250 mv to 3 volts p/p

Triple Drive Based on the highly successful Overdrive Supreme™ SLX, (favorably reviewed in the February Guitar Player Magazine), the Triple Drive Supreme features three footswitchable channels of clean, mean and scream. Available in 50,100 and 150 watt versions, the TDS features a dedicated chime filled “California Clean Channel” with brite, deep, and rock/jazz switches, as well as mid and gain boosts. It's second and third channels are based on our successful Overdrive Supreme clean and mean channels. The amp is controlled by a 6-way footswitch (included), which provides channel switching, as well as independent control of mid and gain boosts for both channels. An extra (separate) footswitch jack for the reverb is also available, as is the artist footswitch option.

The amp features 4, 8 and 16 ohm outputs, a full-time all-tube buffered effects loop with series or parallel operation.

Front Panel Features:
Channel One: brite, deep, rock/jazz, high, mid, low, (with pull mid and gain boosts), (low control pulls for manual channel switch)
Channel Two: brite, deep, rock/jazz, hig, mid, low, (with pull mid, and gain boosts),
Channel Three: Overdrive input control (sets amount and sensitivy of distortion), Overdrive Out (sets level when overdrive is activated). OD out control pulls for manual overdrive activation.
Master output section: Master volume (controls channels 2 and 3 only), accent, and reverb master.

Rear Panel Features:
IEC International standard power connector for detachable power cord.
Fuse holder. AC Power, Standby, Ground polarity, power amp “Response” switch (adjusts output stage sag at high volumes). 4, 8 16 ohm ouputs, FX loop, send level control, send output jack, return level control return input jack, series/parallel switch, effects loop trim control (sets operating level of loop for pedal or line level devices).

Footswitch Jacks:
6-pin XLR connector for remote control of mid and gain boosts (for each channel) as well as channel selection (standard). ¼” footswitch jack for reverb disconnect. Artist footswitch (optional), permits, global mute, fx loop bypass, and reverb bypass.

A single guitar input and separate 4, 8 and 16 ohm outputs on ¼” Cliff jacks are provided.

Features:
¾” solid wood cabinet with durable tolex covering.
Anodized aluminum chassis with long-lasting silk screened labeling on rear panel. Front panel is brushed aluminum and available in black or silver. Crème or black knobs are available. Heavy duty Cliff brand jacks. Solid metal shaft Alpha potentiometers. Ultra-long-life neon pilot lamp and heavy duty AC power, standby, and ground switches. Power stage features AC balance control, and separate bias controls for each power tube.

Like the Overdrive Supreme, the loop features separate send and return level controls, a series/parallel switch and a trim control to permit line or pedal level device interface. The loop inputs and outputs are “live” whether the loop is terminated or not. This means the send output may be used as a line out, and the return input may be used as a spare line level input for a keyboard, drum machine, or other signal input, at any time. The reverb features a spacious Accutronics long decay 6-spring reverb driven by a push-pull current drive amp and an ultra low noise return amp using bi-fet op-amp technology.  Fully adjustable input and output levels. Like the ODS, the Tripledrive™ features fan cooling, an aircraft grade T-6 aluminum chassis, individual tube bias adjusts and regulated B+ and DC preamp tube filaments for lowest noise and consistent performance despite line noise or variations.

The chassis (like all Fuchs products) is aircraft grade aluminum, our internal construction is mixed PC board and hard wired.  A detachable power cord is standard. By using single point grounding, a regulated and buffered high voltage preamp power supply, the amp is dead quiet and free of hum at all operating levels.

Specifications:
Size:
Head:        8” tall, 27.5” wide and 10.50” deep.
Combo:   20” tall, 27.5” wide and 11.00” deep.
Weight (Head):
50 Watt    40 lbs
100 Watt   45 lbs
150 Watt   50 lbs
Weight (Combo):
50 Watt    112  60 lbs
50 Watt    212  75 lbs
100 Watt   112   65 lbs
100 Watt   212   80 lbs
150 Watt   112   75 lbs
150 Watt   212   90 lbs
Tube compliment: 5 X 12AX7 preamp tubes,
2 X 6L6 power tubes (50 Watt)
4 X 6V6 (custom 50 version)
4 X 6L6 tubes (100 Watt version)
4 X 6550 (150 Watt version) 
Power output: 50, 100 or 150 watts RMS into into 4, 8, or 16 ohms.
Input Impedance -1 Meg.

FX Loop:
Output impedance 1-K. Signal; level up to 3 volts p/p
Return impedance 100-K sensitivity from 250 mv to 3 volts p/p.

Fuchs Audio Technology combo amps and cabinets are now shipping standard with the new Eminence Wizard 12” guitar driver. These new speakers are part of the new Red Coat line from Eminence, and are designed to emulate the sound of the classic G12H-30 Celestion speaker, known for being one of the most popular most tonally balanced drivers for guitar. It features an English-made cone, on an American made stamped basket, with a 56 oz magnet and 1.75” voice coil diameter.

Op voorraad als head, in  50 en 100 watt

Representing a new direction for Fuchs Audio Technology, the Lucky 7^TM brings the high build quality and awesome tone's people expect of Fuchs products to a new more affordable price range. The Lucky 7^TM is based on a dual 12AX7 preamp stage and a unique single ended 7-watt EL-34 fixed bias output stage. By switching to a 6V6, you can reduce power to less than 5-watts. Unlike other amps in this price range, the Lucky 7^TM has a full compliment of extremely flexible tone controls. A surprising amount of clean headroom is available before the output stage begins distorting with a sweet yet cutting rock edge. Voiced like its bigger siblings the Train 45^TM and Blackjack 21, the Lucky 7^TM has a classic rock voice similar to a vintage Marshall^TM or Trainwreck^TM style amp. It provides a cutting rock edge, yet filled with harmonic richness and chime. The circuit design also is "attenuator friendly". (*) The Lucky 7^TM and its higher powered sibling the Blackjack 21^TM have a preamp stage designed to allow clean-to-mean from the guitar volume control.

The chassis (like all Fuchs products) is aircraft grade aluminum; our internal construction is mixed PC board and hard wired. On the Lucky 7^TM and Blackjack 21^TM, the preamp tubes and power supply circuitry are on the circuit card, while the power tubes and transformer are mounted on the chassis. A detachable power cord is standard. By using single point grounding, the amp is quiet and free of hum at all operating levels.

A single input and single ¼" output jack are provided.
fuchs-lucky7-35003

Features:
¾" solid wood cabinet with durable tolex covering.
Anodized aluminum chassis with long-lasting silk screened labeling
Heavy duty Cliff brand jacks. Solid metal shaft Alpha potentiometers.
Ultra-long-life neon pilot lamp and heavy duty AC power switch. Simple user adjustable fixed bias.
L7collage02
Specifications:
Size: 8" tall 10.5 inches deep 19" wide.
Weight: 10-lbs.
Tube compliment: 2 X 12AX7 preamp tubes, 1 X EL-34 power tube.
Power output: 7-watts into 8 or 4 ohms.
Input Impedance -1Meg. Output impedance 8 Ohms.
L7-faceplate-350

we hebben ze op voorraad de prijs € 949 .00